The solutions that best meet your requirements is A. Organize the OUs at the top level by department; then use group accounts to help control resource rights.
Which solution meets the requirement?Since you want to create a tree of organizational units (OUs) for the business that can adapt to rapid development without requiring immediate reorganization. Additionally, you ought to be able to quickly assign permissions to particular network resources based on organizational departmental responsibilities in the real world. The best course of action in this situation is to first group the OUs at the highest level by country, and then use group accounts to help the rights of control resource.
RMM remote management technology should be used if you want to periodically check on the health of these laptops and be able to get automatic notifications for any unusual activity that might indicate a security breach.
Learn more about organizational unit on:
https://brainly.com/question/28346734
#SPJ1
Complete question
You want to create a tree of organizational units (OUs) that can adapt to the rapid growth without re-organizing the OU structure in the near future. You also want to be able to easily assign rights to certain network resources based on departmental organizational roles.
Which of the following solutions BEST meet your requirements.
A. Organize the OUs at the top level by department; then use group accounts to help control resource rights
B. Organize the Ous at the top level by employee and resource, then assign specific rights to each user.
C. Organize the OUs at the top level by resource and office (country); then assign specific rights to each user.
D. Organize the OUs at the top level by office (country); then use group accounts to help control resource rights
Determine the critical load if the bottom is fixed and the top is pinned. ewew = 1. 6 ×(10)3ksi×(10)3ksi ,σyσy = 5 ksiksi
Critical load Fcr or buckling load is the value of load that causes the phenomenon of change from stable to unstable equilibrium state.
With that beign said, first it is neessary to calculate the moment of inercia about the x-axis:
\(Ix= \frac{db^3}{12}\\ Ix = \frac{2.(4)^3}{12} = 10.667in\)
Then it is necessary to calculate the moment of inercia about the y-axis:
\(Iy = \frac{db^3}{12}\\ Iy = \frac{4.(2)^3}{12} = 2.662in\)
Comparing both moments of inercia it is possible to assume that the minimun moment of inercia is the y-axis, so the minimun moment of inercia is 2662in.
And so, it is possible to calculate the critical load:
\(Pc\gamma = \frac{2046\pi ^2E.I}{L^2} \\Pc\gamma= \frac{2046.\pi ^2.(1,6.10^3.10^3).2662}{(10.12)^2} \\Pc\gamma= 5983,9db\)
See more about critical load at: https://brainly.com/question/22020642
#SPJ1
given 6 , what is the current of the ideal current source, , for which there is no current flowing through the 5 resistor?
There is no current flowing through the 5 resistor, the current of the ideal current source remains 6.
What is resistor?A resistor is an electrical component that resists the flow of electrical current. It usually consists of a conductive material, such as metal, that is wrapped in an insulating material. When current flows through the resistor, the conductive material creates a resistance to the current, causing some of the energy to be dissipated as heat. This resistance is expressed as a unit of measure called ohms. Resistors can be found in most electronic devices, from radios to cell phones.
The current of an ideal current source is always equal to the stated value, regardless of any external conditions. In this case, the ideal current source has a current of 6. Since there is no current flowing through the 5 resistor, the current of the ideal current source remains 6.
To learn more about resistor
https://brainly.com/question/17671311
#SPJ1
Kimber has been tasked with assembling her department's latest updates into a single document. as she combines multiple documents, what's an important word processing skill to know that ensures the end result is organized and easy to use? question 7 options: footnoting animation bookmarking pagination
When it comes to combining multiple documents, an important word processing skill to know that ensures the final result is organized and easy to use is pagination.
Pagination is a page numbering technique that is done sequentially. These page numbers are usually located at the top or bottom of the web page. In most cases, it is used for main pages and partitions in corporate websites. This kind of design can generally make the user experience simpler on the site. They can also feel more comfortable when it comes to distributing and navigating products within the website.
For example, like this, imagine an e-commerce site that consists of hundreds of product catalogs from various categories. Of course, these products will not be found easily if only placed on one page. As a solution, UI developers and designers can take advantage of pagination to make product placement more structured.
Learn more about Pagination here brainly.com/question/17205277
#SPJ4
Why do projects fail and what is needed to help them be successful? Provide references
Many projects fail because of a lack of proper planning and execution.
In order to help them be successful, it is important to have a clear understanding of the project requirements and goals, as well as a well-defined project plan with milestones and deadlines. Communication and collaboration among team members is also crucial, as is the ability to adapt and adjust the plan as needed in response to changing circumstances and new information. Additionally, having a project manager with strong leadership skills and experience can help ensure that the project stays on track and that everyone is working together effectively. Reference:Project Management Institute. (2017). The Project Management Book of Knowledge (PMBOK Guide) (6th ed.).
A strategy for new projects is created through execution planning, which is also known as project management planning. In project management, one of the early stages is this one. During this stage, project supervisors and colleagues take an underlying thought and make a composed execution plan.
Know more about planning and execution, here:
https://brainly.com/question/32091168
#SPJ11
g the following data apply to a single bolt and nut used to fasten together a double d-ring and relates to questions 7 through 10. 8. what external load would just cause the joint to separate?
Based on the given data, the external load that would just cause the joint to separate would depend on the strength and properties of the bolt and nut used to fasten together the double d-ring. Without this information, it is impossible to determine the exact external load required to separate the joint.
Based on your question, to determine the external load that would just cause the joint to separate when fastening together a double D-ring using a single bolt and nut, we need more information about the materials, their properties, and dimensions. Please provide this data so I can give you an accurate answer Without knowing the specific values of the data, it is not possible to determine the external load that would cause the joint to separate. The external load that would cause the joint to separate depends on several factors such as the strength of the bolt and nut, the material properties of the double d-ring, and the type of forces acting on the joint.To determine the external load that would cause the joint to separate, it would be necessary to perform a calculation based on the specific data provided for the bolt, nut, and double d-ring. This would involve analyzing the stress and strain in the components of the joint under the applied load and comparing it to the yield strength of the materials.In general, it is important to ensure that the external load applied to a joint does not exceed the maximum load capacity of the joint. Exceeding the load capacity can result in joint failure and potential safety hazards. Therefore, it is important to follow appropriate design and engineering principles when selecting and using fasteners to ensure the safety and reliability of the joint.
To learn more about separate click on the link below:
brainly.com/question/13619907
#SPJ11
To answer regarding the external load that would just cause the joint to separate when fastening together a double D-ring using a single bolt and nut, we need to consider the following factors:
1. The tensile strength of the bolt
2. The tensile strength of the D-ring
3. The clamping force provided by the bolt and nut
Once we have this information, we can determine the weakest component in the assembly, as that will dictate the external load at which the joint will separate.
Here is a step-by-step explanation of how to find the external load that would cause the joint to separate:
Step 1: Determine the tensile strength of the bolt and the D-ring.
Step 2: Determine the clamping force provided by the bolt and nut.
Step 3: Identify the weakest component in the assembly (either the bolt, D-ring, or clamping force).
Step 4: Use the weakest component's strength to calculate the external load that would cause the joint to separate.
Without specific data for the bolt, D-ring, and clamping force, we cannot provide an exact value for the external load that would cause the joint to separate. However, by following these steps, you can determine the answer once you have the necessary data.
Learn more about D-ring: https://brainly.com/question/31517177
#SPJ11
A pulse-jet baghouse is desired for a finished cement plant. Calculate the number of bags required to filter 500 m3/min of air with a dust loading of 3.0 g/m3. Each bag is 3.0 m long with a 0.13 m diameter. If the average pressure drop is 1.0 kPa and the main fan is 60% efficient, calculate the fan power in kW. If the pulse air volumetric flow rate is 0.5% of the filter airflow rate and the pulse air pressure is 6.0 atm, calculate the power drawn by a 50% efficient compressor (in kW).
Answer:
1) 4.41 * 10^-4 kw
2) 2.20 * 10^-4 kw
Explanation:
Given data:
Filter = 500 m^3/min
dust velocity = 3g/m^3
bag ; length = 3 m , diameter = 0.13 m
change in pressure = 1 kPa
efficiency = 60%
1) Calculate the Fan power
First :
Calculate the total dust loading = 3 * 500 = 1500 g
To determine the Fan power we will apply the relation
\(n_{o} = \frac{\frac{p}{eg*Q*h} }{1000}\) = \(\frac{\frac{p}{(3*10^{-3})* 981*( 500/60) *3 } }{1000}\)
fan power ( \(n_{0}\) ) = 4.41 * 10^-4 kw
2) calculate power drawn
change in P = 6 atm = 6 * 10^5 pa
efficiency compressor = 50%
hence power drawn = 4.41 * 10^-4 kw * 50% = 2.20 * 10^-4 kw
Coal containing 21% ash is completely combusted, and the ash is 100% removed in a water contact scrubber. If 10,000 kg of coal is burned per hour with a scrubber flow rate of 1.0 m3/min, the weight percentage of the ash in the water/ash stream leaving the scrubber is most nearly:_______.
a. 3.4
b. 14.3
c. 25.9
d. 67.7
Answer:
Weight Percentage of Ash = 3.4
Explanation:
Given - Coal containing 21% ash is completely combusted, and the ash is 100% removed in a water contact scrubber. If 10,000 kg of coal is burned per hour with a scrubber flow rate of 1.0 m3/min.
To find - the weight percentage of the ash in the water/ash stream leaving the scrubber is most nearly ?
Solution -
Given that,
Coal Burned Rate = 10,000 kg/hr
= \(\frac{10,000}{60 min} * 1 hr *\frac{kg}{hr}\)
= 166.6666 kg/min
⇒Coal Burned Rate = 166.6666 kg/min
Now,
Given that,
Ash content in coal = 21 %
⇒Ash in (coal that burned) = 166.6666 × \(\frac{21}{100}\) kg/min
= 34.9999 ≈ 35 kg/min
⇒Ash in (coal that burned) = 35 kg/min
Now,
We know,
Density of water = 1000 kg/m³
Now,
Water flow Rate = \(1\frac{m^{3} }{min} * density\)
= 1000 kg/min
⇒Water flow Rate = 1000 kg/min
Now,
Total Mass flow Rate of (Water + Ash stream) = ( 1000 + 35) kg/min
= 1035 kg/min
⇒Total Mass flow Rate of (Water + Ash stream) = 1035 kg/min
So,
Weight Percentage of Ash = (Weight of Ash ÷ Total weight of Stream) × 100
= (35 ÷ 1035) × 100
= 3.38 ≈ 3.4
∴ we get
Weight Percentage of Ash = 3.4
What does it mean to measure a government's deficit "relative to the size of the economy"?
What does it mean to measure a government's deficit "relative to the size of the economy"?
To measure the deficit as a percentage of the economy or GDP.
How does deficit relate to the economy?
An increase in the fiscal deficit, in theory, can boost a sluggish economy by giving more money to people who can then buy and invest more. Long-term deficits, however, can be detrimental for economic growth and stability.
What does it mean when the government is in a deficit?
A deficit occurs when the federal government's spending exceeds its revenues. The federal government has spent $1.10 trillion more than it has collected in fiscal year (FY) 2023, resulting in a national deficit.
Hope this helps :)
Pls brainliest...
1. Gas Metal Arc Welding is also known as
welding.
Answer: metal inert gas (MIG) welding
Explanation:
Gas metal arc welding (GMAW), also called metal inert gas (MIG) welding, is an arc welding process in which the heat for melting the metal is generated by an electric arc between a consumable electrode and the metal (Fig.
compute the densities of totally crystalline and totally amorphous polypropylene
The densities of totally crystalline and totally amorphous polypropylene are 0.96 g/cm³ and 0.855 g/cm³, respectively.
Polypropylene is a type of thermoplastic polymer which has both amorphous and crystalline regions. It is often used in packaging, textiles, and other applications due to its high stiffness, resistance to heat, and good chemical resistance. The densities of totally crystalline and totally amorphous polypropylene can be computed as follows:
The density of totally crystalline polypropylene is approximately 0.96 g/cm³. This value is obtained by measuring the density of highly crystalline polypropylene samples that have been annealed to promote crystal growth. Crystalline polypropylene has a regular, ordered structure that is more dense than the amorphous regions.
The density of totally amorphous polypropylene is approximately 0.855 g/cm³. This value is obtained by measuring the density of polypropylene samples that have been melted and rapidly cooled to preserve their amorphous structure. Amorphous polypropylene has a random, disordered structure that is less dense than the crystalline regions.
In summary, the densities of totally crystalline and totally amorphous polypropylene are 0.96 g/cm³ and 0.855 g/cm³, respectively.
Learn more about polypropylene
https://brainly.com/question/28158007
#SPJ11
when a flare connection leaks due to a bad flare what is the recommended repair
When a flare connection leaks due to a bad flare, the recommended repair involves carefully disassembling the connection and inspecting the flare for damage.
If the flare is damaged or deformed, you should cut off the damaged section of tubing and create a new flare using a flaring tool. Before reassembling the connection, ensure the flare nut and mating surface are clean and free of debris.
After making a new flare, reattach the flare nut and mating surface, then tighten the connection properly to ensure a secure and leak-free seal. It is essential to perform these steps with precision to maintain the system's integrity and prevent future leaks.
Learn more about flaring tool at
https://brainly.com/question/16806314
#SPJ11
A transmitter has an output power of 0.1mW while the fiber has coupling loss of 12dB, attenuation of
6dB/km for the length of 500m. The link contains two connectors of 2dB average loss. The receiver has a
minimum acceptable power ( sensitivity) of -35dBm. The designer has allowed a 4dB margin. Based on
the given information,
a) Calculate total link loss
b) Determine the receiver's sensitivity
c) Identify this system is good practice or not
A pequin walks 10 feet in six second how far does the pequin wals in 45 seconds
Answer:
7.5 feet
Explanation:
45 divided by 6 is 7.5
Answer:
7.5 feet
Explanation:
45 divided by 6 is 7.5
Which alpha-numeric designator, systematically assigned at the time of manufacture, identifies the manufacturer, month, year, location, and batch?
An alpha-numeric designator which is systematically assigned at the time of manufacture, so as to identify the manufacturer, month, year, location, and batch is referred to as lot number.
What is a product?A product can be defined as any physical object (tangible item) that is typically produced by a manufacturer so as to satisfy and meet the demands, needs or wants of every customer. Also, some examples of a product include the following:
RefrigeratorTelevisionMicrowave ovenPencilSmartphoneComputerPerfumeWhat is lot number?A lot number can be defined as an alpha-numeric designator which is systematically designed and assigned at the time of manufacture, so as to identify the manufacturer, month, year, location, and batch.
Read more on products here: brainly.com/question/14308690
#SPJ1
are there any companies that you can get a job at as an air craft engeer after university
Explanation:
most big airports. my father has the same degree and works for southwest airlines
Hey guys can anyone list chemical engineering advancement that has been discovered within the past 20 years
An air conditioner operates exactly as a refrigerator; it removes heat from a cold place (a bedroom, for example) and conveys it to a warmer place (usually the outside). Quantities of practical importance in understanding the efficiency of air conditioners are the rate of heat removal and the electric power input to the unit (i.e., the electric energy consumed per unit time). Find an expression for the coefficient of performance KKK of an air conditioner that has a rate of heat removal HHH and a power consumption PPP .
The expression for coefficient of heat performance is; K = H/P
We are given the expressions;
Coefficient of performance = K
Rate of heat removal = H
Power consumption = P
Formula for coefficient of performance is usually;
K = Q/W
However, the rate of heat removal H can be further expressed as;
H = Q/T
Where;
Q is heat removed
T is time
Similarly, for power consumption, it can also be expressed as;
P = W/T
Where;
W is workdone
T is time taken
Thus, Q = HT and W = PT
Finally;
K = HT/PT
K = H/P
Read more about coefficient of performance at; https://brainly.com/question/13756267
With the changing demand patterns, fewer full bins are being required and a
greater proportion of goods need to be picked at the picking stations. What
alternatives may be considered to accommodate this?
Should home shopping continue to have its own dedicated area within the
SANDC, with its own inventory and OSR equipment? How flexible is a
SANDC to such changes in demand patterns, and what are likely to be the key
implementation issues for any future operational change?
• Continuous improvement is being sought in all operations. How can the present
SANDC operation be improved still further in terms of efficiency, service levels,
ergonomics and sustainability? What areas may be worthy of examination?
The alternative that could be thought of in order to accommodate changing demand patterns is to increase the number of bins to manage the picking of orders which would accommodate a large number of orders from diverse customers.
What alternatives may be considered to accommodate this?
To accommodate changing demand patterns, the number of picking stations and number of pickers can also be increased in order to manage the orders of customers efficiently.
Home shopping should continue to have its own dedicated area within the SANDC, with its own inventory and OSR equipment as it helps for easier assemblage and storage.
Learn more about demand on:
https://brainly.com/question/1245771
#SPJ1
emitter, base, and collector are the terminals of a?
rated load capacities, recommend operating speeds, and special hazard
Rated load capacities, recommended operating speeds and special hazards or instructions may be posted On all equipment.
What is rated load capacity?It is a term that connote that a machine's rated capacity is said to be at its peak or maximum weight and it is one that can be used to lift in the weakest possible configuration.
Therefore, Rated load capacities, recommended operating speeds and special hazards or instructions may be posted On all equipment
Learn more about operating speeds from
https://brainly.com/question/4931057
#SPJ1
See full question below
Rated load capacities, recommended operating speeds and special hazards or instructions may be posted
What are some suggestions on how to make a balaclava tighter?
You can try several things to make your balaclava tighter if it's too loose or doesn't fit properly. Some suggestions are as follows :
1. By Adjust the drawstring: You can adjust the fit of most balaclavas by adjusting the drawstring. Try tightening the drawstring on your balaclava if it has one.
2. Wear a hat or beanie underneath Adding some extra bulk to your balaclava can help fill out the space if it is too loose around the head.
3. Use a hair tie: The excess fabric on your balaclava can be gathered up with a hair tie if it's too loose around your neck.
4. Sew in some elastic: To create a tighter fit, you can sew some elastic into the balaclava if you are handy with a needle and thread
5. Buy a smaller size: The balaclava may need to be purchased in a smaller size if none of these suggestions work.
Thus, you can try several things to make your balaclava tighter.
learn more about drawstring here :
https://brainly.com/question/33658291
#SPJ4
If you want to revise a sketch or a feature when using a 3D CAD program, how do you make a correction without using the undo function
Answer:
See explanation
Explanation:
Truthfully, this answer can vary depending on the CAD program you are choosing to use. Generally, you go to your model tree (this has been on the left hand side of the screen in all of the CAD software I have used) and click the sketch or feature to edit. In some programs this is a left click and in others this is a right click. When the feature is correctly selected a menu should appear with the option to edit feature/sketch/definition/etc. Select this option and you should be able to edit what you wanted to.
Which component in an ignition system is responsible for raising the voltage?
The ignition coil is the crucial part in an ignition system that increases the voltage.
Why is this so important?It is essentially a transformer, capable of boosting the low voltage of a battery to the high voltage necessary for generating a spark at the plug - generally ranging between 20,000 and 50,000 volts.
The construction of the coil entails two coils of wire encircling an iron core, connected by either some breaker points or an electronic switch. As electricity passes through the primary coil, a magnetic field arises, inducing a high voltage in the secondary coil resulting in the generation of a spark.
Read more about voltage here:
https://brainly.com/question/1176850
#SPJ1
Un estudiante inventa cierta escala de temperatura a presión normal y cumple con los siguientes parámetros: punto de congelación del agua es -60 ˝B, y su punto de ebullición es -10 ˝B. Calcule la temperatura Kelvin que corresponda a 0 ˝B. porfa:(
Answer:
La temperatura Kelvin que corresponde a 0 ºB es 493.15 Kelvin.
Explanation:
Sabemos que el punto de congelación del agua es 273.15 Kelvin y, según el enunciado, -60 ºB. Asimismo, el punto de ebullición de esta sustancia es 373.15 Kelvin y, según el enunciado, -10 ºB. Asumiendo una relación lineal, podemos determinar la temperatura en escala Kelvin equivalente a 0 ºB mediante la siguiente extrapolación:
\(T = 373.15\,K+\left[\frac{373.15\,K-273.15\,K}{-10\,^{\circ}B-(-60\,^{\circ}B)}\right]\cdot [0\,^{\circ}B-(-60\,^{\circ}B)]\)
\(T = 493.15\,K\)
La temperatura Kelvin que corresponde a 0 ºB es 493.15 Kelvin.
The ground temperature a few meters below the surface is fairly constant throughout the year and is near the average value of the air temperature. In areas in which the air temperature drops very low in the winter, the exterior unit of a heat pump designed for heating is sometimes buried underground in order to use the earth as a thermal reservoir.Why is it worthwhile to bury the heat exchanger, even if the underground unit costs more to purchase and install than one above ground?
Since the Earth contains a constant temperature range heat exchangers can be built underground without other added expenses yes they are expensive to put underground but the pay off is greater long term wise since the heat rises it can be said you could put a heatpump in a small area and it can over time increase the relative heat in that area of effect.
hope this helps look into, heat displacement thru underground heating to get a clearer picture
a is truefor every non empty family of sets. let the universe be r, and let a be the empty family of subsets of r. show that is false
"a is true for every non-empty family of sets" for the empty family of subsets of R (the real numbers) is FALSE.
Analyze this step by step.
1. Define the terms:
- Universe (U): R (the set of all real numbers)
- A: the empty family of subsets of R, denoted as ∅
2. Consider the given statement:
- "a is true for every non-empty family of sets."
3. Examine the case when the family of subsets is empty (A = ∅):
- Since A is empty, it does not contain any subsets of R. This means it is not a non-empty family of sets.
4. Determine if the statement is false for the empty family of subsets:
- The given statement specifically mentions "non-empty" family of sets, which implies that the statement does not apply to empty family of sets like A = ∅. So, we cannot conclude whether the statement is true or false for the empty family of subsets, as it is not addressed by the statement.
In conclusion, the given statement "a is true for every non-empty family of sets" does not apply to the empty family of subsets of R (A = ∅). As a result, we cannot show whether the statement is false for the empty family, as it is not within the scope of the statement.
For more questions on subsets
https://brainly.com/question/17514113
#SPJ11
Two kg of a two phase liquid vapor mixture of carbon dioxide(co2) exists at a - 40C in a 0.05 tank
The question is incomplete. Here is the complete question.
Two kg of a two phase liquid vapor mixture of carbon dioxide (CO₂) exists at -40°C in a 0.05m³ tank. Determine the quality of the mixture, if the values of specific volume for saturated liquid and saturated vapor CO₂ at -40°C are \(v_{f}\) = 0.896 x 10⁻³m³/kg and \(v_{g}=\) 3.824 x 10⁻²m³/kg, respectively.
Answer: x = 1
Explanation: In a phase change of a pure substance, at determined pressure and temperature, the substance exists in two different phases: saturated liquid and saturated vapor.
Quality (x) is the ratio of saturated vapor in the mixture and can be written as:
\(x=\frac{m_{vapor}}{m_{liquid}+m_{vapor}}\)
It has value between 0 and 1: x = 0 for saturated liquid and x = 1 for saturated vapor.
When related with volumes, quality is rearranged as:
\(x=\frac{v-v_{f}}{v_{g}-v_{f}}\)
Solving for x:
\(x=\frac{0.05-0.896.10^{-3}}{3.824.10^{-2}-0.896.10^{-3}}\)
\(x=\frac{0.049104}{0.037344}\)
x = 1.3
Quality of mixture of carbon dioxide is x = 1, which means it's for saturated vapor.
Engine oil flows in a 15-cm-diameter horizontal tube with a velocity of 1.3 m/s, experiencing a pressure drop of 12 kPa. The pumping power required to overcome this pressure drop in W is
Given:Velocity of the engine oil, v = 1.3 m/s Diameter of the horizontal tube, D = 15 cm = 0.15 m Pressure drop, ΔP = 12 kPa.
We know that: Pumping power required = (Pressure drop × Volume flow rate) ÷ Efficiency Volume flow rate, Q = πD²/4 × vQ = π(0.15)²/4 × 1.3Q = 0.01335 m³/s= 13.35 L/s Substitute the values: Pumping power required = (12 kPa × 0.01335 m³/s) ÷ 0.70 Pumping power required = 226.9 W
Therefore, the pumping power required to overcome this pressure drop is 226.9 W (rounded off to the nearest tenth).Note: The efficiency value is not given. It is assumed as 0.70 (typical efficiency value of pumps).
To know more about efficiency visit :
https://brainly.com/question/30861596
#SPJ11
a simply supported beam has a length of 1.2 m. the cross section has a width of 140 mm and height of 240 mm. the weight density of the beam is 5.4 kn/m3 . calculate the maximum permissible value of the load p if (a) the allowable bending stress is 8.5 mpa, and (b) the allowable shear stress is 0.8 mpa.
The results of the calculations are (a) P = 37.97 kN and (b) P = 35.62 kN.
The surface won't be cut if you press the flat section of the knife against the fruit. The force is dispersed over a wide area.
Using the parameters and figure provided in the problem, we have:
A = b*h = 0.14*0.24 = 0.0336 m^2
S = (b*h^2)/6 = (0.14*0.24*0.24)/6 = 0.001344 m^3
q = 5400*0.0336 = 181.44 N/m
(a) The load P at 8.5 MPa = 8.5*106 Pa (allowable bending stress)
σ = M/S
M = *S thus equals 0.001344*8.5*106 = 11424 Nm.
Aside from that
M = (P*L/4) + (q*L^2)/8
11424 = (P*1.2/4) + (181.44*1.2^2)/8
11424 = 0.3*P + 32.6592
P = (11424-32.6592)/0.3 = 37.97 kN
(b) If (allowable shear stress) = 0.8 MPa, then the value of P is equal to 0.8*106 Pa.
(2*A*τ/3) = P/2 + q*L/2
(2*0.0336*0.8*10^6)/3 = P/2 + 181.44*1.2/2
17920 = P/2 + 108.864
P = (17920 - 108.864) * 2 = 35.62 kN.
Learn more about stress here-
https://brainly.com/question/13261407
#SPJ4
Which step in the reverse-engineering process involves the identification of subsystems and their relationship to one another?
The answer is analyze