Which type of truck-trailer combination has the greatest chance of a "crack-the-whip" rollover?1. A tractor pulling three trailers2. A single tractor trailer 3. A tractor pulling two trailers

Answer:

33.1144 °C

Explanation:

From the information given;

The first step is to find the mean temperature \(T_m\) by using the formula:

\(T_m = \dfrac{T_i- T_\infty}{2}\)

where:

\(T_i\) = initial temperature = 40 °C

\(T_{\infty}\) = ambient temperature = 10 °C

\(T_m = \dfrac{(40+10)^0C}{2}\)

\(T_m = \dfrac{50^0C}{2}\)

\(T_m\)  = 25 °C

\(T_m\)  = (25 + 273) K

\(T_m\)  = 298 K ≅ 300 K

The following properties expressed below were obtained from the thermal physical properties table.

For soda-lime glass at the temperature of 300 K:

Density \(\rho_s = 2500 \ kg/m^3\)

Thermal conductivity \(k_s\) = 1.4 W/m.K

Specific heat \((c_p)_s\) = 750  J/kg.K

For bakelite at the temperature of 300 K:

Density \(\rho_B = 1300 \ kg/m^3\)

Thermal conductivity \(k_B\) = 1.4 W/m.K

Specific heat \((c_p)_B\) = 1465  J/kg.K

From these data; The next process is to find out the thermal diffusivity of each component.

To start with soda-lime glass by using the expression:

\(\alpha_s = \dfrac{k_s}{\rho_s ( c_p)_s}\)

\(\alpha_s = \dfrac{1.4 \ W/m.K}{2500 \ kg/m^3 \times 750 \\J/kg.K}\)

\(\alpha_s = 747 \times 10^{-9} \ m^2/s\)

For Bakelite: The thermal diffusivity is computed as:

\(\alpha_B = \dfrac{k_B}{\rho_B ( c_p)_B}\)

\(\alpha_B = \dfrac{1.4 \ W/m.K}{1300 \ kg/m^3\times 1465 \ J/kg.K}\)

\(\alpha_B = 735 \times 10^{-9} \ m^2/s\)

From the above two results, we will realize that \(\alpha _ s \simeq \alpha _B\)

Thus, as obvious as it is; we presume that the uniform thermal diffusivity

\(\alpha = 740 \times 10^{-9} \ m^2/s\)

However, the diameter of the sphere can be estimated by the summation of the diameter of the glass sphere \((D_1)\) with twice the thickness of the sphere (L)

i.e. \(D = D_1 + 2L\)

D = 25 mm + 2 (10 mm)

D = 45 mm

\(D = 45 \ mm ( \dfrac{10^{-3} \ m}{1 \ mm} )\)

D = 45 × 10⁻³ m

The expression for Biot Number can be estimated by using the formula:

\(Bi = \dfrac{hL}{k}= \dfrac{h(D/6)}{k}\)

Given that:

h = 30 W/m².k

D = 45 × 10⁻³ m

k = 1.4 W/m.K

Similarly, to estimate the Fourier No \(F_o\) by using the expression:

\(F_o = \dfrac{\alpha t}{(D/2)^2}\)

\(F_o = \dfrac{740 \times 10^{-9} \ m^2 /s \times 200 \ s}{( \dfrac{45 \times 10^{-3} m}{2})^2}\)

\(F_o = 0.292\)

It is obvious that \(F_o\) is > 0.2, thus, the validity of one term approximation is certain.

Again; the Biot Number is calculated by using the formula:

\(Bi = \dfrac{h(D/2)}{k}\)

\(Bi = \dfrac{30 \ W/m^2.K (\dfrac{45 \times 10^{-3 }\ m}{2}) }{1.4 \ W/m.k}\)

Bi = 0.482

Bi \(\simeq\) 0.5

We obtain the Eigen coefficient \(\xi_1\) as well as the coefficient for a sphere \(C_1\) using the Bi Number:

From one-term approximation of transient 1 heat conduction in the sphere;

\(\dfrac{T - 10^{0 } \C }{40^{0} \ C - 10^0 \ C} = 1.1441 \ exp \ ( -1.1656^2 \times 0.291)\)

\(\dfrac{T - 10^{0 } \C }{30^{0} \ C} = 0.77048\)

\(T - 10^{0 } \C = 30^{0} \ C \times 0.77048\)

\(T - 10^{0 } \C = 23.1144^0 \ C\)

T = (23.1144 + 10) °C

T = 33.1144 °C

Lazy Deletion, as we have implemented it in a general tree, is good for avoiding garbage collection for a small number of removal calls, conserving memory, and fast removal.

However, it is not good for fast insertion as it has a higher complexity than other tree deletion techniques, such as eager deletion.In order to implement a Boolean function that does not have a simple algebraic or logical description, a method that has an O along if statement can be used.In the scenario where Bob defines a base class, Base, with instance method func(), but does not declare it to be virtual, and Alicia (who has no access to Bob's source code) defines three derived classes, Der1, Der2 and Der3, of the base class and overrides func(), Ying can call p->func() on each object in the loop and get distinct behavior as defined by the object pointed to, and Ying can call p->func() on each object in the loop and get no compiler error.

To know more about garbage collection visit:

brainly.com/question/28592522

#SPJ11

Answer:

Reflection

Explanation:

The specific behavior of light that will be essential to ensure the success of your design is "Reflection". This is because light maze makes use of a mirror and it's the light that is reflected that we see with our eyes. Also, the manner in which light is reflected off objects will affect the colors that are reflected as well.

Answer:

a) The amount by which this specimen will elongate in the direction of the applied stress is 0.466 mm

b) The change in diameter of the specimen is  - 0.015 mm

Explanation:

Given the data  in the question;

(a) The amount by which this specimen will elongate in the direction of the applied stress.

First we find the area of the cross section of the specimen

A = \(\frac{\pi }{4}\) d²

our given diameter is 20.5 mm so we substitute

A = \(\frac{\pi }{4}\) ( 20.5 mm )²

A = 330.06 mm²

Next, we find the change in length of the specimen using young's modulus formula

E = σ/∈

E = P/A × L/ΔL

ΔL = PL/AE

P is force ( 46300 N), L is length ( 201 mm ), A is area ( 330.06 mm² ) and E is  elastic modulus (60.5 GPa) = 60.5 × 10⁹ N/m² = 60500 N/mm²

so we substitute

ΔL = (46300 N × 201 mm) / ( 330.06 mm² × 60500 N/mm² )

ΔL =  0.466 mm

Therefore, The amount by which this specimen will elongate in the direction of the applied stress is 0.466 mm

(b) The change in diameter of the specimen. Indicate an increase in diameter with a positive number and a decrease with a negative number.

Using the following relation for Poisson ratio

μ = -  Δd/d / ΔL/L

given that Poisson's ratio of the metal is 0.33

so we substitute

0.33 = -  Δd/20.5 / 0.466/201

0.33 = -  Δd201 / 20.5 × 0.466

0.33 = - Δd201  / 9.143

0.33 × 9.143 =  - Δd201

3.01719 = -Δd201

Δd = 3.01719 / - 201

Δd  = - 0.015 mm

Therefore, The change in diameter of the specimen is  - 0.015 mm

True. Doxygen can be described as a multi-programming-language Javadoc.

Doxygen is a documentation generator tool that is not only limited to Java, but also supports various programming languages, including C++, C, Objective-C, Python, and others. It was created as an alternative to Javadoc, which specifically focuses on Java documentation.

The main purpose of Doxygen is to extract comments and documentation from the source code and generate comprehensive, navigable, and easily understandable documentation. It is commonly used by developers and programmers to create well-documented software products.

Doxygen allows users to create both inline and external documentation for their code. Inline documentation is written directly within the source code as special comments, while external documentation is written separately and linked to the code.

In addition to the versatility in language support, Doxygen also provides a wide range of output formats, such as HTML, LaTeX, RTF, XML, and more. This makes it highly customizable and adaptable to different project needs.

Overall, describing Doxygen as a multi-programming-language Javadoc is true, as it shares similar features and purposes with Javadoc, while extending its support to multiple programming languages and providing additional functionalities.

Know more about the Javadoc click here:

https://brainly.com/question/13382879

#SPJ11

Answer:

True

Explanation:

It's just because of the processing

The volume of cuboid in cubic feet which must be ordered is equal to 5,600 cubic feet.

Given the following data:

Length of helicopter landing pad = 40 ft.

Width of helicopter landing pad = 70 ft.

Height or thickness of helicopter landing pad = 2 ft.

Based on the information provided, we can reasonably infer and logically deduce that the shape of this helicopter landing pad is a cuboid.

Mathematically, the volume of a cuboid can be calculated by using this following formula:

Volume = l × w × h

Where:

Substituting the given parameters into the formula, we have;

Volume = 40 × 70 × 2

Volume = 5,600 cubic feet.

Read more on volume of a cuboid here: https://brainly.com/question/24919497

#SPJ1

A factor which is most significant in the lobbying efforts of the energy and natural resources industry include the following: C. Their economic resources allow them to support full-time professional lobbyists and staff researchers.

An interest group simply refers to a group that is composed of individuals who are primarily concerned with influencing various policies of the government based only on their interests, common aims, cause, goals, or people they represent.

In Sociology, a lobbyist can be defined as an activist whose endeavor and intent is to persuade government officials to enact laws (legislation) and policies that would significantly benefit their group at large.

This ultimately implies that, an energy and natural resources industry may seek to increase energy efficiency through lobbying for policy changes by investing more money and other economic resources in order to allow them support full-time professional lobbyists and staff researchers.

Read more on interest groups here: https://brainly.com/question/25656843

#SPJ1

Complete Question:

Which of the following factors is most significant in the lobbying efforts of the energy and natural resources industry?

a. Their focus on supporting social services makes them popular throughout the state.

b. Their alliance with several state environmental interests amplifies their voice.

c. Their economic resources allow them to support full-time professional lobbyists and staff researchers.

d. Their large member base motivates many members of the legislature to vote in their favor.

e. Their efforts to avoid electoral politics help them maintain a strong reputation.

check photo solve

check photo solve

check photo solve

the smallest allowable outer diameter (d) of the washers is approximately 50.82 mm, considering the average normal stress in the bolts and the bearing stress between the washers and the planks.

The average normal stress in the bolts is given as 36 MPa, which is equal to 36 N/mm².

So, σ_avg = 36 N/mm² = 36 MPa

The bearing stress between the washers and the planks must not exceed 8.5 MPa, which is equal to 8.5 N/mm².

So, σ_bearing = 8.5 N/mm² = 8.5 MPa

Now, using the relationship between the bearing stress and the average normal stress:

σ_bearing = σ_avg * (d_bolt / d_washer)

8.5 = 36 * (12 mm / d_washer)

Now, solve for d_washer:

d_washer = 36 * 12 mm / 8.5

d_washer =  50.82 mm

Since the washer's inner diameter is 16 mm, the difference between the inner and outer diameters of the washers is 2 * t (the thickness of the washers).

So, d_washer - 16 mm = 2 * t

t = (d_washer - 16 mm) / 2

t ≈ (50.82 mm - 16 mm) / 2

t ≈ 17.41 mm

Read more about  the average normal stress here:

https://brainly.com/question/14293037

#SPJ3

ᴄᴏᴍᴘʟᴇᴛᴇɴᴇꜱꜱ ᴍᴇᴀɴꜱ ᴛʜᴇ ꜱᴛᴀᴛᴇ ᴏꜰ ʙᴇɪɴɢ ᴄᴏᴍᴘʟᴇᴛᴇ ᴀɴᴅ ᴇɴᴛɪʀᴇ; ʜᴀᴠɪɴɢ ᴇᴠᴇʀʏᴛʜɪɴɢ ᴛʜᴀᴛ ɪꜱ ɴᴇᴇᴅᴇᴅ.

ʙᴇᴀᴜᴛʏ ᴍᴇᴀɴꜱ combination of qualities, such as shape, colour, or form, that pleases the aesthetic senses, especially the sight.

The the minimum hamming distance required between codes to correct up to two bit errors in a block is 3.

The hamming distance between two codewords is the number of bits in which they differ. In order to correct up to two bit errors in a block, the minimum hamming distance required should be greater than or equal to three. This is because if two bits are flipped in a codeword, then the hamming distance between the erroneous codeword and the correct codeword will be two, and the decoder will not be able to determine which of the two bits was flipped. However, if the minimum hamming distance between codes is three, then there will always be at least a distance of three between any two codewords, which means that the decoder can correct up to two bit errors.

To know more about Minimum hamming visit:-

https://brainly.com/question/31982816

#SP11

We combine multiplication and addition to translate the inputs to dollars and cents.

The Python program that uses comments to describe each line is as follows:

The number of quarters is input here.

Quarters = int("Quarters: ")

#This is given the input of the amount of dimes.

dime = int("Dimes: ") input

This takes as input the quantity of nickels.

nickels = int("Nickels: ") input

This is given the input of how many pence.

pennies = int("Pennies: ") input

Using this, the sum is changed to dollars and cents.

Dollars equal quarters times 0.25, dime times 0.10, nickel times 0.05, and penny times 0.01

#This displays the amount with two digits.

format(dollars) print("Amount $:.2f".Amount)

Learn more about input here-

https://brainly.com/question/24179864

#SPJ4

Answer:

winter viscosity grades

Explanation:

The “W”/winter viscosity grades describe the oil's viscosity under cold temperature engine starting conditions. There's a Low Temperature Cranking Viscosity which sets a viscosity requirement at various low temperatures to ensure that the oil isn't too thick so that the starter motor can't crank the engine over.

Grade 5 bolts have 3 marks identifying on the head

This is further explained below.

Generally,  When looking for the correct bolt, it is essential to check that the grades of the bolts that are currently being used are compatible with one another.

There is no difference between Grade 5 Bolts and Metric.

8 Bolts. The presence of three marks on the head of a Grade 5 bolt is often all that is required for successfully identifying the bolt.

In conclusion, The head of a grade 5 bolt will have three distinguishing markings on it.

Read more about  Grade 5 bolts

https://brainly.com/question/14900098

#SPJ1

Answer:

When you build a compressor that is supposed to run in an enclosed system you want the coolant medium (and the lubricants) in this system to function optimally during the service life of the system.

First of all, the coolant medium has a tendency to absorb water and this moisture can be aggressive on the internal components of the compressor so you want to remove this once the system is sealed.

Second, you want to filter out any particles that may shorten the life of the system.

Those are the two purposes of the liquid line filter drier in the refrigeration system.

Explanation:

A fixed end beam is a type of support structure that is commonly used in construction and engineering projects. It is designed to provide stability and support to a load or structure by anchoring it firmly to a foundation or other structure.

The fixed end beam is a type of support structure that is designed to prevent any movement or rotation at the point of support.When it comes to the ability of a fixed end beam to rotate at the point of support, the answer is actually "None of the above." A fixed end beam is designed to be rigid and immobile at the point of support, which means that it cannot rotate or move in any way. The fixed end beam is designed to transmit loads and forces to the support structure through a combination of bending and shear forces.The ability of a fixed end beam to transmit bending moments to the support is one of its most important characteristics. When a load is placed on the beam, it will bend and deform under the weight, but the fixed end beam will remain rigid and stable, allowing it to transfer the load to the support structure without any issues. This is essential for maintaining the stability and integrity of the entire structure.In conclusion, a fixed end beam is a type of support structure that is designed to be rigid and immobile at the point of support. It is capable of transmitting bending moments to the support, but it cannot rotate or translate at the point of support. This is an important factor to consider when designing and constructing any type of structure or load-bearing component.

Learn more about engineering here

https://brainly.com/question/28321052

#SPJ11

DNA analysis plays a crucial role in forensic science because it provides irrefutable evidence to identify suspects, victims, and even remains. It is a highly reliable method that allows investigators to match DNA samples found at a crime scene to a suspect or exclude innocent individuals from the investigation.

This helps to solve cases faster and more accurately, ensuring that justice is served. DNA analysis is also helpful in exonerating the wrongly accused, which is critical to upholding the integrity of the criminal justice system. Overall, DNA analysis is an essential tool in forensic science that helps to ensure that the right person is held accountable for their actions and the innocent are protected from false accusations.

The importance of DNA analysis to the field of forensic science lies in its ability to provide accurate and reliable evidence for criminal investigations. DNA analysis allows forensic scientists to. Identify suspects: By comparing DNA samples found at a crime scene with those of potential suspects, investigators can establish a match, proving a suspect's presence at the crime scene or involvement in the crime. Exonerate the innocent: DNA analysis can also clear innocent individuals by demonstrating that their DNA does not match the evidence found at the crime scene, preventing wrongful convictions. Solve cold cases: DNA analysis can be used to re-examine unsolved cases, even after many years, providing new leads and potentially identifying the perpetrator.
To know  more about investigators visit :

https://brainly.com/question/29365121

#SPJ11

Answer:

yes maybe

Explanation:

I have a project and everyone in the world will know about it.

Answer:

both

Explanation:

Answer:

Primary cell with a nominal open circuit voltage of 1.5 Volts produced in very high volumes. Chemistry based on a zinc anode and a cathode/depolariser of manganese dioxide which absorbs the liberated hydrogen bubbles which would otherwise insulate the electrode from the electrolyte.

Answer:

Explanation:

(1) The electrolyte is a paste of ammonium chloride.

(2) The positive terminal (anode) is a carbon rod surrounded bymangAnese Dioxide as a depolarised .

(3) The negative terminal is zinc container.

Answer:

Purpose of review papers

They carefully identify and synthesize relevant literature to evaluate a specific research question, substantive domain, theoretical approach, or methodology and thereby provide readers with a state-of-the-art understanding of the research topic.

Answer: 72 inches!

Explanation:

The length of the rectangular yard in inches is 72 inches. This is calculated by using the perimeter formula, p = 2l + 2w, and substituting the known values: p = 2(18 feet) + 2(4 feet). This simplifies to p = 36 feet + 8 feet, which is equal to 44 feet. To convert this to inches, we multiply 44 feet by 12 inches per foot, which gives us a total of 528 inches. Therefore, the length of the rectangular yard in inches is 72 inches.

Answer:

Hello There!!

Explanation:

The answer is territorial.

hope this helps,have a great day!!

~Pinky~

\(\huge{\textbf{\textsf{{\color{navy}{An}}{\purple{sw}}{\pink{er}} {\color{pink}{:}}}}}\)

The county is normally the state's largest political and Territorial unit.

Answer:

The basic difference between Total cost and total revenue is that the total cost includes the total expenditure incurred on the production of a commodity whereas total revenue refers to the money received from selling that commodity.

Explanation:

Answer:

Here, in America we use more than 300 gallons of water per day.

Explanation:

I looked it up sooo- yeah.

And I hope this helped,

Answer:

The answer is below

Explanation:

1) The synchronous speed of an induction motor is the speed of the magnetic field of the stator. It is given by:

\(n_s=\frac{120f_s}{p}\\ Where\ p\ is \ the \ number\ of\ machine\ pole, f_s\ is\ the\ supply \ frequency\\and\ n_s\ is \ the \ synchronous\ speed(speed \ of\ stator\ magnetic \ field)\\Given: f_s=60\ Hz, p=4. Therefore\\\\n_s=\frac{120*60}{4}=1800\ rpm\)

2) The speed of the rotor is the motor speed. The slip is given by:

\(Slip=\frac{n_s-n_m}{n_s}. \\ n_m\ is\ the \ motor\ speed(rotor\ speed)\\Slip = 0.05, n_s= 1800\ rpm\\ \\0.05=\frac{1800-n_m}{1800}\\\\ 1800-n_m=90\\\\n_m=1800-90=1710\ rpm\)

3) The frequency of the rotor is given as:

\(f_r=slip*f_s\\f_r=0.04*60=2.4\ Hz\)

4) At standstill, the speed of the motor is 0, therefore the slip is 1.

The frequency of the rotor is given as:

\(f_r=slip*f_s\\f_r=1*60=60\ Hz\)

The following Unified Endpoint Management (UEM) features can help an IT administrator manage and administer IT assets: software deployment, remote management, user provisioning, and license management.

These features allow administrators to efficiently deploy software, remotely manage devices, provision user accounts, and manage software licenses.

Unified Endpoint Management (UEM) is a solution that enables IT administrators to manage and secure a wide range of devices and endpoints from a single console. Among the given features, software deployment is a key UEM capability that allows administrators to distribute and install applications across multiple devices simultaneously. This feature streamlines the deployment process and ensures that all devices are equipped with the necessary software.

Remote management is another important UEM feature that enables administrators to monitor and control endpoints from a centralized location. It provides administrators with the ability to troubleshoot issues, perform updates, and enforce security policies remotely, saving time and resources.

User provisioning is a UEM feature that simplifies the process of creating and managing user accounts on various devices and platforms. Administrators can provision user profiles, set access permissions, and manage user roles and groups, ensuring efficient user management across the organization.

License management is a crucial UEM feature that allows administrators to track and manage software licenses effectively. It helps ensure compliance with licensing agreements, prevents unauthorized software usage, and optimizes license allocation and utilization.

Operating system deployment, although not mentioned in the summary, is not a UEM feature. It typically falls under the domain of Mobile Device Management (MDM) or PC lifecycle management solutions, which focus on deploying and managing operating systems on devices. UEM solutions may integrate with MDM or PC lifecycle management tools to provide comprehensive endpoint management capabilities.

learn more about software licenses here: brainly.com/question/30174221

#SPJ11