Dimensions should be placed__
the drawing whenever possible__lines should not cross dimension lines
Answers
Answer:
dimensions should be placed OUTSIDE the drawing whenever possible THE lines should not cross dimension lines
Explanation:
Related Questions
A happy, excited driver
is less impaired than an angry driver.
is never affected by passengers in the vehicle.
is a safe driver.
can be just as impaired as an angry driver.
Answers
Answer:
A happy,excited driver
can be just as impaired as an angry driver
locução adjetiva e de portuges ou istoria
Answers
Which of the following uses pressure and flow to transmit power from one location to another?
acoustics
propulsion
pumps
fluid power
Answers
Answer:
fluid power
Explanation:
fluids commonly used in fluid power are Oil, Water, Air, CO², and Nitrogen gas, fluid power is commonly confused with hydraulic power, which only uses liquids, fluid power uses either liquids or gases
The Engineering Design Process is used to:
Answers
Answer:
to find a solution to a problem.
Explanation:
The engineering design process, by definition, is a series of steps that engineers use to find a solution to a problem. These steps include: defining the problem, brainstorming solutions, designing and building a prototype of the solution, testing the solution, and improving it.
what is the meaning of 52k?
Answers
Answer:
52K is a form of money or amount. It basically means 52,000.
Explanation:
K stands for thousand.
. A spring was at its resting position where it is attached to a wall at its left side and a block at its right side as shown below. The spring constant is k=25.0 N/m. The block is moved leftwards and the spring's right end is displaced from the position of 0.250m to .200m. All positions are measured from the origin OOO of the wall. What is the spring force exerted on the block
Answers
The force of spring will be "3.75 N". The further explanation is given below.
How to explain the force.It should be noted that a force is an influence that causes the motion of an object with mass to change its velocity, i.e., to accelerate. It can be a push or a pull, always with magnitude and direction, making it a vector quantity.
The given values are:
Spring constant, K = 75.0 N/m
x₁ = 0.200 m
x₂ = 0.150 m
x = 0.200 - 0.15
= 0.05
Force will be:
= 75 × 0.05
= 3.75N
Learn more about force on
https://brainly.com/question/16737255
#SPJ1
Can someone help here’s a picture
Answers
Answer:
6--b
7--a
8--c
9--f
10--d
Explanation:
6. Miter saw/circular blade with perimeter teeth (b.wood/metal sheet)
7. Miter saw/circular blade with 60+ teeth. (a.ceramic tile)
8. Circular saw/circular blade with abrasive. (c. fine cuts on expensive molding)
9. Reciprocating saw/straight blade, bimetal. (f. solid metal)
10. Circular saw/circular blade with grinding edge, dry. (d. demolition having old nails)
About circular sawA circular saw is a type of cutting tool in the form of a chainsaw with a round and serrated saw blade. With this type of saw, cutting wood becomes easier. Not only that, Circular Saw is also often chosen because of the practicality of its use. In addition, this circular saw is also very practical to remove. So if the saw blade is dull, then you can easily remove it to be sharpened again, or replaced with a new one.
Learn more about circular saw at
https://brainly.com/question/17157503
#SPJ1
According to the NC SDIP, if you get a ticket for going 45 MPH in a 35 MPH zone, you would see a
increase in insurance premiums for
Select one:
O a. 10%, 3 years
O b. 30%, 3 years
O c. 80%, 5 years
d. 45%, 2 years
Answers
According to the NC SDIP (North Carolina Safe Driver Incentive Plan), if you get a ticket for going 45 MPH in a 35 MPH zone, you would see an increase in insurance premiums for 30%, 3 years.
Here,
NC SDIP is a program created by the North Carolina Department of Insurance to encourage safe driving practices. The program assesses insurance points to drivers based on certain traffic violations or accidents.
So,
If you get a traffic ticket, the number of insurance points you receive will depend on the type of violation. If you get a ticket for going 45 MPH in a 35 MPH zone, you would receive two insurance points.
This would result in a 30% increase in insurance premiums for the next three years.
Therefore option B is correct.
Know more about insurance ,
https://brainly.com/question/989103
#SPJ4
explanation of dip painting method
Answers
Answer:
Explanation:
Dip painting is a process in which an object is immersed or dipped in a tank or vat of paint, typically a liquid or powder coating, to coat the object's surface evenly. The object is first cleaned and prepared before it is dipped into the paint, and then it is lifted out and left to dry.
The dip coating process involves several steps, including surface preparation, selecting the right type of coating, and dipping the object into the paint. First, the object's surface must be free of any debris, grease, or other substances that may interfere with the paint's adhesion. This can be done by washing or sanding the surface, depending on the type of material.
Next, the type of coating to be used is selected. This can depend on several factors, such as the desired finish, the durability required, and the type of material the object is made from. Once the coating is selected, the object is dipped into the paint tank or vat, which is usually kept at a constant temperature and viscosity to ensure a consistent finish.
Asbestos can be dangerous but is not a known carcinogen.
Answers
Answer:
False.
Explanation:
Asbestos is a known carcinogen (a substance that is known for causing cancer), recognized by the U.S. Department of Health and Human Services (HHS).
______________________________________________________
Learn more at: https://brainly.com/question/8853025
Have a WONDERFUL day! (:
Answer:False
Explanation:
QUESTION 1: Different Line Types Look at the drawing of a different bicycle pump below. This drawing is accurate, so we call it a scale draw It is four times smaller than a real pump. We say it is drawn to a scale of 1:4. That means that if you meas the length of the outer tube of this drawing, it will be four times smaller than the outer tube of the real pu F + 320 Figure 9: Bicycle pump. Scale 1:4 Why is the outer tube of this pump drawn with solid lines?
Answers
Answer:
The outer tube of the pump is drawn with solid lines because it represents the visible edges of the object, which are the most important and prominent features of the drawing. Solid lines are used to indicate visible edges, while other types of lines such as dashed or dotted lines are used for hidden or construction lines that are not meant to be seen in the final drawing.
Explanation:
When drawing an object, it's important to distinguish between the visible edges and the hidden or construction lines. The visible edges are the lines that represent the outer contour or silhouette of the object, which define its shape and form. In the case of the bicycle pump, the outer tube is the most prominent and recognizable feature of the pump, so it's drawn with solid lines to emphasize its importance and to make it stand out from the other parts of the pump.
On the other hand, the hidden or construction lines are used to guide the drawing process, to show the internal structure or components of the object, or to indicate the position of other features that are not visible from the current viewpoint. These lines are usually drawn with dashed or dotted lines to distinguish them from the visible edges and to avoid confusion.
By using different types of lines, the artist can create a clear and accurate representation of the object, with all the relevant information conveyed in a concise and understandable way. This is especially important in technical or scientific drawings, where precision and clarity are essential for conveying complex ideas or designs.
What happens to the electrolyte, during discharging?
Answers
on any given day, one person needs an average of 2.5 liters of water to survive. how many people will a tank supply for the day
Answers
Answer:
3936 people
Explanation:
Water Tank = 9840 liters of water.
Now divide the total amount of water available by the amount of water needed per person to get the number of people that can consume all the water:
9840 Liters / (2.5 Liters/ 1 person) =
1 person * 9840 Liters / 2.5 Liters =
1 person * 9840/2.5 = 3936 people
Perchuty (P. z fan ce the Treffe resistivalyThe law of resistivity.
Answers
We can see here that the law of resistivity, also known as Ohm's law, states that the electrical resistance of a conductor is directly proportional to its resistivity and length, and inversely proportional to its cross-sectional area.
How is law of resistivity represented?The Law of resistivity can be mathematically represented as:
R = ρ × (L / A)
Where:
R is the electrical resistance of the conductor,
ρ (rho) is the resistivity of the material,
L is the length of the conductor, and
A is the cross-sectional area of the conductor.
The resistivity (ρ) is a characteristic property of a material that quantifies its ability to resist the flow of electric current. It depends on the nature of the material, its temperature, and sometimes its purity. Resistivity is measured in ohm-meters (Ω·m).
Learn more about resistivity on https://brainly.com/question/30611906
#SPJ1
PLS ANSWER QUICKLY
Communication can take the form of: A.Spoken/verbal, non-verbal, electronic, written B.Spoken/verbal, non-verbal, written, visuals C.Effective, verbal, non-verbal, electronic D.Effective, ineffective, verbal, written
Answers
Answer:
Option B
Explanation:
Communication can be of following types -
a) Verbal - Through Speaking
b) Non Verbal - Through expression
c) Writing - in written form
d) Visuals - by seeing
Hence, option B is the right choice of answer
As people enter the hotel and look at the ceiling, they see a huge chandelier whose lights enhance the carvings on the ceiling. Which structural element is preventing the chandelier from causing cracks on the roof?
Answers
The structural element that is preventing the chandelier from causing cracks on the roof is option B. plate.
What keeps a chandelier in place?It is firmly fastened to a wood block or joist. Make sure the ceiling box is rated to sustain your chandelier fixture as the most of them can support 50 to 75 pounds. Remove the present ceiling fan or light fixture.
Therefore, To hold it, The finest option is a heavy, robust chain that is split on the side (never on the bottom). There is a base plate on some chandeliers. The chandelier is bolted onto the base plate once it has been put on the ceiling.
Learn more about chandelier from
https://brainly.com/question/27853369
#SPJ1
See options below
A column
B. plate
C beam
D. true
why does high resistance not affect a parallel circuit
Answers
Answer:
Because the equivalent or the total resistance is lower comparatively.
Explanation:
It is because in parallel circuit, the equivalent resistance or the total resistance is lower comparatively and hence more current flow through the circuit.
Basically, the same resistors connected in series have high values as compared to the scenario when these resistors are connected in parallel.
Which software do you need to download to use the VEX IQ robot?
Answers
Answer:
VEXcode IQ software.Explanation:
You may programme and operate the VEX IQ robot using the block-based programming tool VEXcode IQ. You can programme the robot's behaviours and movements, such as moving forward, turning, and perceiving its environment, using VEXcode IQ. The programme may be downloaded from the VEX Robotics website and is compatible with Chrome OS, MacOS, and Windows.
To learn more about VEX IQ robot visit: https://brainly.com/question/14999216
a welder performance qualification test on 1" (25.4mm) thick plate. what range of base metal is the welder qualified to weld? How many tension specimens will be tested? And how many side bends will be tested?
Answers
A welder's accomplishment qualification test on an excellent" (25.4mm) thick plate determines their requirement range.
What does passing qualify the welder for?According to AWS D1.1 Structural Welding Code for Steel, passing this test qualifies them to bind base metals with thicknesses 'tween 0.5" (12.7mm) and 2" (50.8mm).
The qualification test requires two pressure specimens, that assess stiffness, and four side bend specimens, which judge ductility and healthiness.
Read more about welding here:
https://brainly.com/question/9450571
#SPJ1
when a bullet is shot in the air the path transversed by bullet is called
Answers
Answer: The trajectory of the bullet is a parabola
Explanation:
When you shoot a bullet up from a flat plane and never hit anything the bullet will eventually hit the ground due to gravity
Think in terms of shooting a basketball but really far, the balls path will make a parabola shape
Answer:
When a bullet is shot in air, the path traversed by bullet is called parabola.
Hope this helps :)
Pls brainliest...
what would be the power required to exert 6-N force over 3 m in 2 seconds
A. 4w
B.6W
C.9W
D.12W
E.18W
Answers
Answer: 9 W
Explanation:
The power formula is P = W over time, and W is equal to force times distance.
So, let's find W first.
W = 6 * 3 = 18
Now, P is 18/2 = 9 W
GMA (MIG) welding is a:
A) laser welding process.
B)
fusion welding process.
C)
pressure welding process.
D) resistance welding process.
Answers
Answer: Fusion
Explanation:
It has a tendency to fuse stuff
The correct answer is Option B).
GMA (MIG) welding is a fusion welding process.
Given data:
GMA (Gas Metal Arc) welding, also known as MIG (Metal Inert Gas) welding, is a fusion welding process. In GMA/MIG welding, a consumable electrode wire is used to create an electric arc between the wire and the workpiece. The arc heats and melts the base metals, and a shielding gas, typically a mixture of argon and carbon dioxide, is used to protect the weld pool from atmospheric contamination.
During the welding process, the molten electrode wire and the base metal fuse together to form a solid weld joint. This fusion of the materials is characteristic of fusion welding processes, where the base metals are melted to create the weld.
Hence, GMA/MIG welding is considered a fusion welding process.
To learn more about fusion welding process, refer:
https://brainly.com/question/28335634
#SPJ6
Black marks in your solder is a sign of a dry sponge.
True or False
Answers
Black marks in your solder is a sign of a dry sponge is a False statement.
How come my solder is black?When exposed to air, metals oxidize, and if handled improperly, heated metal can oxidize more quickly. This may result in a tough, crusty buildup that is blackish-brown in color and difficult to remove. Your work will be significantly hampered by this buildup, which obstructs the heat transfer from the iron tip to the solder.
Therefore, A black mark is that one could also try lowering the amount of solder used because it's not getting hot enough. The flux made of resin left behind those dark blotches. In contrast to rosin, no-clean fluxes are frequently made of water-soluble resins, and the majority of them will evaporate during heating.
Learn more about solder from
https://brainly.com/question/28377850
#SPJ1
You are driving on a two-way street, and are looking for a place to park;
Answers
Answer:
you cannot park
Explanation:
except you park in a compound because it is a two way road parking on either side could lead to accident or goslow
Geometry no links
Need help
Answers
Technician a says that when more air is entering a spray booth than is removed it is considered to have negative pressure technician b say the negative air pressure draws more overspray through spray booth filters than positive air pressure Who’s right
Answers
In a spray booth, when the amount of air entering the booth is greater than the amount of air being removed, it is considered to have positive pressure. Conversely, when the amount of air being removed is greater than the amount of air entering, it is considered to have negative pressure. Therefore, Technician A's statement is incorrect.
On the other hand, Technician B's statement is correct. Negative air pressure can draw more overspray through spray booth filters because it creates a vacuum effect that draws in the overspray and helps prevent it from escaping into the rest of the work area. This is why spray booths are designed to have a negative pressure differential to help control overspray and keep the work environment safe.
Technician A is correct in stating that when more air is entering the spray booth than is being removed, it is considered to have negative pressure. Negative pressure means that the pressure inside the spray booth is lower than the pressure outside. This setup helps to contain the overspray and fumes within the booth, minimizing the risk of spreading them to the surrounding areas.
Technician B is also correct in stating that negative air pressure draws more overspray through the spray booth filters than positive air pressure. When the spray booth has negative pressure, it creates a suction effect. This suction draws the overspray particles towards the filters, improving their efficiency in capturing and removing the overspray from the air.
In summary, both technicians are correct in their statements. The negative pressure in the spray booth helps contain the overspray, and it also enhances the effectiveness of the booth's filters in capturing the overspray particles.
What kind of analysis would be conducted to identify project costs?
A. competitive analysis
B. customer needs analysis
C. financial analysis
D. concept analysis
Answers
Answer: C. financial analysis
Explanation:
I want descriptions on
Current State of Programming in Pakistan
Scope of Programming in Pakistan
Answers
The scope of BS computer science in Pakistan is quite vast
try this :)
Explain, using at least three reasons, why Timothy would fail to be a good match as a mechanical engineer in the following scenario.
Situation: Timothy is a very shy, reserved person. He is very artistic and creative, but math and science were never his strong subjects. As he enrolls in college classes, he is looking to be exposed to many different careers. He would like to go to an office every day, complete his work, and leave with a sense of accomplishment. He does not enjoy long-standing projects and assignments.
Answers
When making a new product, why might designers and engineers go through the
design process more than once?
A. Designers and engineers repeat
the design process to make sure
that all tests will go exactly
according to plan.
C. Designers and engineers repeat
the design process to address
different parts of their design, or
improve their design further.
B. Designers and engineers only go
through the design process once
when designing a product.
D. Both A and B
Answers
Answer:C. Designers and engineers repeat
the design process to address
different parts of their design, or
improve their design further.
Explanation:just took it